Dragino SN50v3-CB/CS CAT-M/LTE-M Sensor Node

SN50v3-CB/CS CAT-M/LTE-M Sensor Node

SN50v3-CB/CS is a Long Range CAT-M/LTE-M Sensor Node.  It is designed to facilitate developers to quickly deploy industrial level CAT-M/LTE-M solutions. It helps users to turn the idea into a practical application and make the Internet of Things a reality. It is easy to program, create and connect your things everywhere.

SN50v3-CB/CS wireless part is based on model allows the user to send data and reach extremely long ranges at low data-rates. It provides ultra-long range spread spectrum communication and high interference immunity whilst minimizing current consumption. It targets professional wireless sensor network applications such as irrigation systems, smart metering, smart cities, building automation, and so on.

SN50v3-CB/CS CAT-M/LTE-M Sensor Node uses STM32l0x chip from ST, STML0x is the ultra-low-power STM32L072xxxx microcontrollers incorporate the connectivity power of the universal serial bus (USB 2.0 crystal-less) with the high-performance ARM® Cortex®-M0+ 32-bit RISC core operating at a 32 MHz frequency, a memory protection unit (MPU), high-speed embedded memories (192 Kbytes of Flash program memory, 6 Kbytes of data EEPROM and 20 Kbytes of RAM) plus an extensive range of enhanced I/Os and peripherals.

SN50v3-CB/CS is an open source product, it is based on the STM32Cube HAL drivers and lots of libraries can be found in ST site for rapid development.

SN50v3-CB/CS supports different uplink methods including MQTT, MQTTs, UDP & TCP for different application requirement, and support uplinks to various IoT Servers.

SN50v3-CB/CS supports BLE configure and OTA update which make user easy to use.

SN50v3-CB is powered by 8500mAh Li-SOCI2 battery, it is designed for long-term use up to several years. SN50v3-CS is powered by Solar Panel + 3000mAh Li-ion battery.

SN50v3-CB/CS is installed with 10 years NB-IoT Card (500MB)

• CAT-M1 / LTE-M Bands: B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B26/B27/B28/B66/B85
• Ultra-low power consumption
• Open-source hardware / software
• Multiply Sampling and one uplink
• Support Bluetooth v5.1 remote configure and update firmware
• Uplink via MQTT, MQTTs, TCP, or UDP
• Uplink on periodically
• Downlink to change configure
• 8500mAh Battery (CB), Solar panel + 3000mAh Battery (CS)
• Installed with 10 years NB-IoT Card (500MB)

Applications:

• Smart Buildings & Home Automation
• Logistics and Supply Chain Management
• Smart Metering
• Smart Agriculture
• Smart Cities
• Smart Factory

Common DC Characteristics:

• Supply Voltage: 2.5v ~ 3.6v
• Operating Temperature: -40 ~ 85°C

I/O Interface:

• Battery output (2.6v ~ 3.6v depends on battery)
• +5v controllable output
• 3 x Interrupt or Digital IN/OUT pins
• 3 x one-wire interfaces
• 1 x UART Interface
• 1 x I2C Interface

CAT-M Module: BC660K-GL

Support Bands:

• B1 @H-FDD: 2100MHz
• B2 @H-FDD: 1900MHz
• B3 @H-FDD: 1800MHz
• B4 @H-FDD: 2100MHz
• B5 @H-FDD: 860MHz
• B8 @H-FDD: 900MHz
• B12 @H-FDD: 720MHz
• B13 @H-FDD: 740MHz
• B17 @H-FDD: 730MHz
• B18 @H-FDD: 870MHz
• B19 @H-FDD: 870MHz
• B20 @H-FDD: 790MHz
• B25 @H-FDD: 1900MHz
• B28 @H-FDD: 750MHz
• B66 @H-FDD: 2000MHz
• B70 @H-FDD: 2000MHz
• B85 @H-FDD: 700MHz

Battery:

• Li/SOCI2 un-chargeable battery (CB)
• Capacity: 8500mAh (CB)
• Li-ion battery (CS)
• Capacity: 3000mAh (CS)
• Self Discharge: <1% / Year @ 25°C
• Max continuously current: 130mA
• Max boost current: 2A, 1 second

Power Consumption:

• STOP Mode: 10uA @ 3.3v
• Max transmit power: [email protected]